Fatigue behavior of medium-density polyethylene pipes

A round bar specimen and a square bar specimen cut out from medium-density polyethylene pipes with a notch were made and a fatigue test was conducted to cause a brittle fracture. The initiation and growth of a craze and crack at the tip of a notch was observed. In the range where loading cycles are few and displacement of the specimen does not increase, the craze prior to crack initiation occurs. Also, the effect of frequency was investigated. The pure creep failure and the fatigue failure at low frequency were compared. The lower the frequency, the smaller the reciprocal of the actual loading time T_f becomes. It is also found that this tensile fatigue test is a useful test method to assure the quality of pipes.     

Interactions oftrans-cinnamic acid,its related phenolic allelochemicals,and abscisic acid in seedling growth and seed germination of lettuce

Phenolic compounds have been identified as the most common allelochemicals produced by higher plants. Inhibitions of cinnamic acid, its related phenolic derivatives, and abscisic acid (ABA) on seedling growth and seed germination of lettuce were studied.trans-Cinnamic acid, ando-,m-, andp-coumaric acids inhibited the growth of etiolated seedlings of lettuce at concentrations higher than 10^–4 M and seed germination above 10^–3 M. Coumarin inhibited seedling growth and seed germination at 10^–5 M or above. Chlorogenic acid inhibited seedling growth above 10^–4 M, but did not inhibit seed germination at 10^–5–5×10^–3 M. Low concentrations (below 10^–3 M) of caffeic and ferulic acids promoted the elongation of hypocotyls, but higher concentrations (over 10^–3 M) inhibited seedling growth and seed germination. These phenolic compounds and abscisic acid had additive inhibitory effects both on seedling growth and seed germination. The inhibition on lettuce was reversed by caffeic and ferulic acids at concentrations lower than 10^–3 M except for the inhibition of germination by coumarin. These results suggest that in naturetrans-cinnamic acid,o-, m-, p-coumaric acids, coumarin, and chlorogenic acid inhibit plant growth regardless of their concentration. However, caffeic and ferulic acids can either promote or inhibit plant growth according to their concentration.     

An analysis of ball-and-race milling part II. The babcock E 1.7 mill

A mathematical model was developed for a ball-and-race mill based on specific rates of breakage and primary fragment distributions. The model includes internal classification of particles falling back into the race and external classification due to the built-on classifier. It was demonstrated that the normalized primary fragment distribution produced in a pilot-scale Babcock E-type mill of 17 in. race diameter was the same as in the Hardgrove laboratory test mill and that the specific rates of breakage varied with particle size in the same manner. Steady-state continuous tests on the pilot-scale mill showed that breakage rates depended on the rate of feed, since the mill pulled less power at low feed rates. This effect plus the residence time effect gave coarser product size distributions at low and high feed rates than at a medium feed rate. Model simulations based on parameters measured in the Hardgrove mill correctly predicted the product size distribution from the E-type mill.     

Thermal Expansion of Solid Solutions in the ZrTiO4—In2O3—M2O5 (M = Sb, Ta) System

Axial and dilatometric thermal expansions and phase transformations were studied for solid solutions having the α-PbO₂ structure in the ZrTiO₄—In₂O₃—M₂O₅ (M = Sb, Ta) system with nominal formulas of Zr _x Ti _y In _z Sb _z O₄ and Zr _x Ti _y In _z Ta _z O₄ where x + y + 2 z = 2. With increased substitution of z , the cell volume increased, the difference in the b parameters at room temperature between those quenched from 1400° and 1000°C decreased, and the thermal expansion decreased. The axial thermal expansion of ZrTi _y In _z · Ta _z O₄ with z = 0.3 was almost identical with that of HfTiO₄, and those with z = 0.4 and z = 0.45 were smaller than that of HfTiO₄. Unit-cell volumes of these compound were compared with those of single oxides to make it clear that the unit-cell volume of ZrTiO₄ was small anomalously and to distinguish the normal and abnormal substitution systems. These results were explained by the working hypothesis proposed for these compounds.     

Environmentally friendly coloured materials: cellulose/titanium dioxide/inorganic pigment composite spherical microbeads prepared by viscose phase-separation method

In order to develop environmentally friendly coloured materials, cellulose composite spherical microbeads hybridised with titanium dioxide (TiO₂) particles and inorganic pigment were prepared by a phase-separation method using viscose and an aqueous solution containing sodium polyacrylate. Findings regarding the relationships between cellulose xanthate and the electronic characteristics of TiO₂ particles used in the cellulose/inorganic material composite sphering process are also reported. These findings suggest that the location of TiO₂ particles in cellulose microbeads is related to electrical repulsion between the xanthate (CSS⁻) group and TiO₂. The use of TiO₂ powder as colour pigment is limited, as its colour is white. The cellulose composite spherical microbeads covered with TiO₂ and Fe₂O₃ particles were developed by addition of iron oxide (Fe₂O₃). Their surfaces were viewed by laser microscope and using SEM images. These composite microbeads retained the photocatalytic property of TiO₂. Cellulose/TiO₂/Fe₂O₃ composite spherical microbeads with both colour function and photocatalytic properties were successfully prepared.     

Spherical Aluminum Nitride Fillers for Heat-Conducting Plastic Packages

It is necessary for encapsulants to have not only a suitable coefficient of thermal expansion (CTE) compatible to IC devices and a low dielectric constant to reduce the device propagation delay, but also a high thermal conductivity to dissipate large amounts of heat from power-hungry, high-speed IC and high-density packages. Fillers such as silica have been mixed with polymers to improve their properties. Aluminum nitride (AlN) is considered as an alternative one, because it has a higher theoretical thermal conductivity of ∼320 W/mK¹, a compatible CTE with silicon chips and a low dielectric constant. Commercial AlN fillers are angular in shape, because they are prepared via grinding coarse AlN powders synthesized by direct nitridation of aluminum metal and classification. The angular AlN are not expected to have high fluidity when mixed with polymers and hence low packing density. Recently, we successfully obtained single-crystalline spherical AlN fillers. Furthermore, polymer composites filled with the spherical AlN showed excellent thermal conductivity (>8 W/mK) as encapsulants for dissipating the heat generated in electronic devices.     

Development of a high‐resolution RGBW flexible display using a white organic light‐emitting diode with microcavity structure and that of a side‐roll touch panel

In this study, white organic electroluminescent devices with microcavity structures were developed. A flexible high‐resolution active‐matrix organic light‐emitting diode display with low power consumption using red, green, blue, and white sub‐pixels formed by a color‐filter method was fabricated. In addition, a side‐roll touch display was developed in combination with a capacitive flexible touch screen.     

Aging and availability of binocular disparity and pictorial depth cues in 3D graphics contents

Some stereoblind observers do not perceive depth of 3D stimuli that depends on binocular disparity. These individuals, who have no disabilities, comprise over 5% of the general population. In addition, 17–30% of nonstereoblind young and young–middle people do not use disparity information in certain 3D environments, a phenomenon known as pseudo‐stereoblindness. This study aimed to investigate the relationship between aging and the proportion of pseudo‐stereoblindness in the general population. In an experiment, 134 nonstereoblind participants, ranging in age from 17 to 83 years, judged subjective depth of 3D stimuli containing binocular disparity and pictorial depth cues. Results showed that the proportion of pseudo‐stereoblindness among young (17–24 years old) and young–middle aged observers (25–39 years old) was 29%, in both cases. However, the proportion of pseudo‐stereoblind observers increased in older populations: 65% and 82% in the middle (40–54 years old) and senior (55–83 years old) age groups, respectively. These results suggest that a number of people, especially in elderly populations, have trouble perceiving depth from binocular disparity in 3D graphic contents despite their essential ability to use disparity information.     

Grafting of poly(ethylene oxide) onto C60 fullerene using macroazo initiators

In order to improve the solubility of C₆₀ fullerene in conventional solvents, grafting of hydrophilic poly(ethylene oxide) (PEO) by utilizing the radical-trapping nature of C₆₀ fullerene was investigated. Macroazo initiators containing a poly(ethylene oxide) unit, known as Azo-PEO, were prepared at various molecular weights by the reaction of 4,4′-azobis(4-cyanopentanoyl chloride) with poly(ethylene glycol) methyl ether. PEO radicals formed by thermal decomposition of Azo-PEO were successfully trapped by C₆₀ fullerene to give PEO-grafted C₆₀ fullerene. Their structures were confirmed by FT-IR spectroscopy, size exclusion chromatography, UV-vis spectroscopy, and differential scanning calorimetry. When Azo-PEO with low-molecular weight was reacted with C₆₀ fullerene, a bis-adduct, C₆₀-(PEO)₂, and a tetrakis-adduct, C₆₀-(PEO)₄, were formed. In contrast, in reactions with Azo-PEO of higher molecular weight, only the bis-adduct was formed, and no formation of the tetrakis-adduct was observed. The structure of bis-adduct was found to be 1,4-type. The solubility of C₆₀ fullerene in water, THF, methanol, and other conventional organic solvents was remarkably improved by grafting of PEO. In addition, the thermal stability of PEO was dramatically increased by grafting onto C₆₀ fullerene.     

Phase separation behavior and morphology development of phenolic resin/PMMA/hexamethylenetetrarnine blends

Summary In order to obtain materials with nanopores which will be applicable for many fields, the structures of the cured blends of phenolic resin (PhN), poly(methyl methacrylate) (PMMA) and curing agent were studied. After PMMA was extracted from cured blends, the structures of cured phenolic resins were observed with SEM. As a results, it was found that nanosized continuous pore structures were formed in extremely wide composition region if curing temperature was high.